Networking

Home

Vendors

Products

Networking

2687 -- 2-channel Reconfigurable 155 Mb/s FO: (from Technobox, Inc.)
FPGA-based reconfigurable platform for implementing fiber optic interfaces that are not supported by standard chipsets. Altera Flex 10K70 standard; other population options may be available. Separate transmit/receive channels. Front-panel I/O (ST type). PCI interface implemented in PLX 9080.

2894 -- 10/100-TX Ethernet with Front and Rear IO: (from Technobox, Inc.)
Single-port 10/100TX Ethernet PMC. RJ45 jack and status/activity indicator LEDs on front panel. AMD 79C973 chipset.

3006 -- 100-FX Ethernete FO (SC Duplex): (from Technobox, Inc.)
The 3006 is a single-port, fiber optic Ethernet adapter built around AMD 79C973. Fiber optic connector is SC Duplex style. Status/activity indicator LEDs on front panel. On-board flash memory for BIOS storage.

3059 -- 100-FX Ethernet FO (ST TX/RX): (from Technobox, Inc.)
The 3059 is a single-port, fiber optic Ethernet adapter built around AMD 79C973. Fiber optic connector is ST TX/RX style. On-board flash memory for BIOS storage.

3293 -- i82559 Ethernet with Front and Rear IO: (from Technobox, Inc.)
The 3293 is a single-port 10/100-TX Ethernet PMC that can provide wither front or rear I/O connectivity as determined by DIP switch settings. Intel 82559. RJ45 jack and status/activity indicator LEDs on front panel. On-board flash memory holds BIOS for booting.

CCII CDDI PMC: (from CCII Systems (Pty) Ltd)
MLT-3 signalling over copper UTP media. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Dual 1 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
Dual, full-duplex, 1 Gbps Fibre Channel communication links on shielded, twisted-pair copper media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.

CCII Dual 2 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
Dual, full-duplex, 2 Gbps Fibre Channel communication links on short-haul or long-haul singlemode fibre media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Front-panel I/O only.

Available in three air-cooled grades: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Ruggedised version is ideally suited for environments with high temperature, shock and vibration levels.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.

CCII Dual 4 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
The Dual 4 Gbps Fibre Channel PMC Adapter offers dual 4 Gbps Fibre Channel communication links on multimode or singlemode fibre media. This adapter provides optimal flexibility by supporting all Fibre Channel topologies, including Arbitrated Loop, with full duplex communications on both channels.

Front-panel I/O only, SFF/LC connectors.

Available in three air-cooled grades : ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C).

Interfaces to 64-bit/133 MHz PCI-X (64-bit/66 MHz and 32-bit/33 MHz compatible) and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386 specification.

Various software drivers offered including for VxWorks, Windows 2000, Windows Server 2003, Windows XP, Solaris X86, Solaris SPARC, SUSE and Red Hat Linux operating systems as standard; others optional.

CCII Dual Gigabit Ethernet PMC: (from CCII Systems (Pty) Ltd)
Dual 10/100/1000 Mbps Ethernet communications links on either copper or fibre media. Uses a custom, intelligent ASIC for the control of the Gigabit Ethernet MACs (Media Access Controllers), thereby removing protocol processing overhead from the host processor, thus providing for higher nett data throughput.

Dual channels provide redundant Gigabit Ethernet links for high system reliability with Redundant Link Management implemented in hardware managing unattended and automatic failure recovery of downed links.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Solaris, Windows 2000, Windows XP and Windows 2003 operating systems as standard; others optional.

CCII FDDI PMC: (from CCII Systems (Pty) Ltd)
Multimode fibre media. ST I/O Connectors. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel or rear facing I/O options.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Air-cooled option mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Video Capture and Compression PMC: (from CCII Systems (Pty) Ltd)
The Video Capture and Compression PMC Adapter generates a compressed video data stream from a standard RS-170 video source using MPEG4 compression implemented in hardware. This compressed video data stream can be output directly on one of four high-speed serial output channels or passed to a host computer via the PCI bus.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Available in three air-cooled grades : Ruggedised (-40 C to +85 C), Industrial (-15 C to +75 C) and Commerical (0 C to +55 C).

Interfaces to 32-bit, 33/66 MHz PCI-bus and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386-2001 specification.

Various software drivers offered including for VxWorks, Linux, Windows NT, Windows 2000* and Windows XP* operating systems as standard; others optional. (*Standard PC HAL only)

CL PMC/100: (from Concurrent Technologies)
10/100Mbps Fast Ethernet controller for VME, Multibus II and CompactPCI. Allows the use of 10BaseT or 100BaseTx with a slimline RJ45 connector. The chip is a highly integrated PCI single-chip bus master which supports direct memory access (DMA) and alleviates the Ethernet protocol load on the host CPU. Supporting ISO 8802-3 (IEEE 802.3 and 802.3u) the board has automatic retransmission, runt frame rejection and selection of received collision frames. Front panel LEDs indicate speed and status of the Local Area Network.

CL PMC/551 Dual Fast Ethernet: (from Concurrent Technologies)
PMC Ethernet Adaptor: A two channel Fast Ethernet adaptor with 10Base-T and 100Base-TX capability. The improved networking performance of the CL PMC/551 is achieved through the use of two Intel� 82551QM Fast Ethernet controllers. These controllers, which have 3Kbyte FIFOs and can operate full-duplex, enable the CL PMC/551 to exhibit improved performance by offloading the TCP, UDP and IP checksums and include support for TCP segmentation offload for operations such as Large Send. The controllers also have improved Bit Error Rate performance and improved dynamic transmit chaining with multiple priorities transmit queues. The adaptor´s physical connection to an Ethernet network is through industry standard RJ45 connectors that allow connection to low cost CAT 5 cabling. The adaptor is targeted at applications that will benefit from reducing the CPU´s Ethernet processing load while maintaining low system latency.

CL PMC/GB1 Dual Gigabit Copper Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.

CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: FPGA-based reconfigurable platform for implementing fiber optic interfaces that are not supported by standard chipsets. Altera Flex 10K70 standard; other population options may be available. Separate transmit/receive channels. Front-panel I/O (ST type). PCI interface implemented in PLX 9080.
2894 -- 10/100-TX Ethernet with Front and Rear IO: (from Technobox, Inc.)
Single-port 10/100TX Ethernet PMC. RJ45 jack and status/activity indicator LEDs on front panel. AMD 79C973 chipset.

3006 -- 100-FX Ethernete FO (SC Duplex): (from Technobox, Inc.)
The 3006 is a single-port, fiber optic Ethernet adapter built around AMD 79C973. Fiber optic connector is SC Duplex style. Status/activity indicator LEDs on front panel. On-board flash memory for BIOS storage.

3059 -- 100-FX Ethernet FO (ST TX/RX): (from Technobox, Inc.)
The 3059 is a single-port, fiber optic Ethernet adapter built around AMD 79C973. Fiber optic connector is ST TX/RX style. On-board flash memory for BIOS storage.

3293 -- i82559 Ethernet with Front and Rear IO: (from Technobox, Inc.)
The 3293 is a single-port 10/100-TX Ethernet PMC that can provide wither front or rear I/O connectivity as determined by DIP switch settings. Intel 82559. RJ45 jack and status/activity indicator LEDs on front panel. On-board flash memory holds BIOS for booting.

CCII CDDI PMC: (from CCII Systems (Pty) Ltd)
MLT-3 signalling over copper UTP media. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Dual 1 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
Dual, full-duplex, 1 Gbps Fibre Channel communication links on shielded, twisted-pair copper media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.

CCII Dual 2 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
Dual, full-duplex, 2 Gbps Fibre Channel communication links on short-haul or long-haul singlemode fibre media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Front-panel I/O only.

Available in three air-cooled grades: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Ruggedised version is ideally suited for environments with high temperature, shock and vibration levels.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.

CCII Dual 4 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
The Dual 4 Gbps Fibre Channel PMC Adapter offers dual 4 Gbps Fibre Channel communication links on multimode or singlemode fibre media. This adapter provides optimal flexibility by supporting all Fibre Channel topologies, including Arbitrated Loop, with full duplex communications on both channels.

Front-panel I/O only, SFF/LC connectors.

Available in three air-cooled grades : ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C).

Interfaces to 64-bit/133 MHz PCI-X (64-bit/66 MHz and 32-bit/33 MHz compatible) and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386 specification.

Various software drivers offered including for VxWorks, Windows 2000, Windows Server 2003, Windows XP, Solaris X86, Solaris SPARC, SUSE and Red Hat Linux operating systems as standard; others optional.

CCII Dual Gigabit Ethernet PMC: (from CCII Systems (Pty) Ltd)
Dual 10/100/1000 Mbps Ethernet communications links on either copper or fibre media. Uses a custom, intelligent ASIC for the control of the Gigabit Ethernet MACs (Media Access Controllers), thereby removing protocol processing overhead from the host processor, thus providing for higher nett data throughput.

Dual channels provide redundant Gigabit Ethernet links for high system reliability with Redundant Link Management implemented in hardware managing unattended and automatic failure recovery of downed links.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Solaris, Windows 2000, Windows XP and Windows 2003 operating systems as standard; others optional.

CCII FDDI PMC: (from CCII Systems (Pty) Ltd)
Multimode fibre media. ST I/O Connectors. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel or rear facing I/O options.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Air-cooled option mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Video Capture and Compression PMC: (from CCII Systems (Pty) Ltd)
The Video Capture and Compression PMC Adapter generates a compressed video data stream from a standard RS-170 video source using MPEG4 compression implemented in hardware. This compressed video data stream can be output directly on one of four high-speed serial output channels or passed to a host computer via the PCI bus.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Available in three air-cooled grades : Ruggedised (-40 C to +85 C), Industrial (-15 C to +75 C) and Commerical (0 C to +55 C).

Interfaces to 32-bit, 33/66 MHz PCI-bus and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386-2001 specification.

Various software drivers offered including for VxWorks, Linux, Windows NT, Windows 2000* and Windows XP* operating systems as standard; others optional. (*Standard PC HAL only)

CL PMC/100: (from Concurrent Technologies)
10/100Mbps Fast Ethernet controller for VME, Multibus II and CompactPCI. Allows the use of 10BaseT or 100BaseTx with a slimline RJ45 connector. The chip is a highly integrated PCI single-chip bus master which supports direct memory access (DMA) and alleviates the Ethernet protocol load on the host CPU. Supporting ISO 8802-3 (IEEE 802.3 and 802.3u) the board has automatic retransmission, runt frame rejection and selection of received collision frames. Front panel LEDs indicate speed and status of the Local Area Network.

CL PMC/551 Dual Fast Ethernet: (from Concurrent Technologies)
PMC Ethernet Adaptor: A two channel Fast Ethernet adaptor with 10Base-T and 100Base-TX capability. The improved networking performance of the CL PMC/551 is achieved through the use of two Intel� 82551QM Fast Ethernet controllers. These controllers, which have 3Kbyte FIFOs and can operate full-duplex, enable the CL PMC/551 to exhibit improved performance by offloading the TCP, UDP and IP checksums and include support for TCP segmentation offload for operations such as Large Send. The controllers also have improved Bit Error Rate performance and improved dynamic transmit chaining with multiple priorities transmit queues. The adaptor´s physical connection to an Ethernet network is through industry standard RJ45 connectors that allow connection to low cost CAT 5 cabling. The adaptor is targeted at applications that will benefit from reducing the CPU´s Ethernet processing load while maintaining low system latency.

CL PMC/GB1 Dual Gigabit Copper Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.

CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Single-port 10/100TX Ethernet PMC. RJ45 jack and status/activity indicator LEDs on front panel. AMD 79C973 chipset.
3006 -- 100-FX Ethernete FO (SC Duplex): (from Technobox, Inc.)
The 3006 is a single-port, fiber optic Ethernet adapter built around AMD 79C973. Fiber optic connector is SC Duplex style. Status/activity indicator LEDs on front panel. On-board flash memory for BIOS storage.

3059 -- 100-FX Ethernet FO (ST TX/RX): (from Technobox, Inc.)
The 3059 is a single-port, fiber optic Ethernet adapter built around AMD 79C973. Fiber optic connector is ST TX/RX style. On-board flash memory for BIOS storage.

3293 -- i82559 Ethernet with Front and Rear IO: (from Technobox, Inc.)
The 3293 is a single-port 10/100-TX Ethernet PMC that can provide wither front or rear I/O connectivity as determined by DIP switch settings. Intel 82559. RJ45 jack and status/activity indicator LEDs on front panel. On-board flash memory holds BIOS for booting.

CCII CDDI PMC: (from CCII Systems (Pty) Ltd)
MLT-3 signalling over copper UTP media. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Dual 1 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
Dual, full-duplex, 1 Gbps Fibre Channel communication links on shielded, twisted-pair copper media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.

CCII Dual 2 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
Dual, full-duplex, 2 Gbps Fibre Channel communication links on short-haul or long-haul singlemode fibre media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Front-panel I/O only.

Available in three air-cooled grades: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Ruggedised version is ideally suited for environments with high temperature, shock and vibration levels.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.

CCII Dual 4 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
The Dual 4 Gbps Fibre Channel PMC Adapter offers dual 4 Gbps Fibre Channel communication links on multimode or singlemode fibre media. This adapter provides optimal flexibility by supporting all Fibre Channel topologies, including Arbitrated Loop, with full duplex communications on both channels.

Front-panel I/O only, SFF/LC connectors.

Available in three air-cooled grades : ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C).

Interfaces to 64-bit/133 MHz PCI-X (64-bit/66 MHz and 32-bit/33 MHz compatible) and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386 specification.

Various software drivers offered including for VxWorks, Windows 2000, Windows Server 2003, Windows XP, Solaris X86, Solaris SPARC, SUSE and Red Hat Linux operating systems as standard; others optional.

CCII Dual Gigabit Ethernet PMC: (from CCII Systems (Pty) Ltd)
Dual 10/100/1000 Mbps Ethernet communications links on either copper or fibre media. Uses a custom, intelligent ASIC for the control of the Gigabit Ethernet MACs (Media Access Controllers), thereby removing protocol processing overhead from the host processor, thus providing for higher nett data throughput.

Dual channels provide redundant Gigabit Ethernet links for high system reliability with Redundant Link Management implemented in hardware managing unattended and automatic failure recovery of downed links.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Solaris, Windows 2000, Windows XP and Windows 2003 operating systems as standard; others optional.

CCII FDDI PMC: (from CCII Systems (Pty) Ltd)
Multimode fibre media. ST I/O Connectors. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel or rear facing I/O options.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Air-cooled option mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Video Capture and Compression PMC: (from CCII Systems (Pty) Ltd)
The Video Capture and Compression PMC Adapter generates a compressed video data stream from a standard RS-170 video source using MPEG4 compression implemented in hardware. This compressed video data stream can be output directly on one of four high-speed serial output channels or passed to a host computer via the PCI bus.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Available in three air-cooled grades : Ruggedised (-40 C to +85 C), Industrial (-15 C to +75 C) and Commerical (0 C to +55 C).

Interfaces to 32-bit, 33/66 MHz PCI-bus and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386-2001 specification.

Various software drivers offered including for VxWorks, Linux, Windows NT, Windows 2000* and Windows XP* operating systems as standard; others optional. (*Standard PC HAL only)

CL PMC/100: (from Concurrent Technologies)
10/100Mbps Fast Ethernet controller for VME, Multibus II and CompactPCI. Allows the use of 10BaseT or 100BaseTx with a slimline RJ45 connector. The chip is a highly integrated PCI single-chip bus master which supports direct memory access (DMA) and alleviates the Ethernet protocol load on the host CPU. Supporting ISO 8802-3 (IEEE 802.3 and 802.3u) the board has automatic retransmission, runt frame rejection and selection of received collision frames. Front panel LEDs indicate speed and status of the Local Area Network.

CL PMC/551 Dual Fast Ethernet: (from Concurrent Technologies)
PMC Ethernet Adaptor: A two channel Fast Ethernet adaptor with 10Base-T and 100Base-TX capability. The improved networking performance of the CL PMC/551 is achieved through the use of two Intel� 82551QM Fast Ethernet controllers. These controllers, which have 3Kbyte FIFOs and can operate full-duplex, enable the CL PMC/551 to exhibit improved performance by offloading the TCP, UDP and IP checksums and include support for TCP segmentation offload for operations such as Large Send. The controllers also have improved Bit Error Rate performance and improved dynamic transmit chaining with multiple priorities transmit queues. The adaptor´s physical connection to an Ethernet network is through industry standard RJ45 connectors that allow connection to low cost CAT 5 cabling. The adaptor is targeted at applications that will benefit from reducing the CPU´s Ethernet processing load while maintaining low system latency.

CL PMC/GB1 Dual Gigabit Copper Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.

CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: The 3006 is a single-port, fiber optic Ethernet adapter built around AMD 79C973. Fiber optic connector is SC Duplex style. Status/activity indicator LEDs on front panel. On-board flash memory for BIOS storage.
3059 -- 100-FX Ethernet FO (ST TX/RX): (from Technobox, Inc.)
The 3059 is a single-port, fiber optic Ethernet adapter built around AMD 79C973. Fiber optic connector is ST TX/RX style. On-board flash memory for BIOS storage.

3293 -- i82559 Ethernet with Front and Rear IO: (from Technobox, Inc.)
The 3293 is a single-port 10/100-TX Ethernet PMC that can provide wither front or rear I/O connectivity as determined by DIP switch settings. Intel 82559. RJ45 jack and status/activity indicator LEDs on front panel. On-board flash memory holds BIOS for booting.

CCII CDDI PMC: (from CCII Systems (Pty) Ltd)
MLT-3 signalling over copper UTP media. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Dual 1 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
Dual, full-duplex, 1 Gbps Fibre Channel communication links on shielded, twisted-pair copper media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.

CCII Dual 2 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
Dual, full-duplex, 2 Gbps Fibre Channel communication links on short-haul or long-haul singlemode fibre media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Front-panel I/O only.

Available in three air-cooled grades: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Ruggedised version is ideally suited for environments with high temperature, shock and vibration levels.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.

CCII Dual 4 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
The Dual 4 Gbps Fibre Channel PMC Adapter offers dual 4 Gbps Fibre Channel communication links on multimode or singlemode fibre media. This adapter provides optimal flexibility by supporting all Fibre Channel topologies, including Arbitrated Loop, with full duplex communications on both channels.

Front-panel I/O only, SFF/LC connectors.

Available in three air-cooled grades : ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C).

Interfaces to 64-bit/133 MHz PCI-X (64-bit/66 MHz and 32-bit/33 MHz compatible) and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386 specification.

Various software drivers offered including for VxWorks, Windows 2000, Windows Server 2003, Windows XP, Solaris X86, Solaris SPARC, SUSE and Red Hat Linux operating systems as standard; others optional.

CCII Dual Gigabit Ethernet PMC: (from CCII Systems (Pty) Ltd)
Dual 10/100/1000 Mbps Ethernet communications links on either copper or fibre media. Uses a custom, intelligent ASIC for the control of the Gigabit Ethernet MACs (Media Access Controllers), thereby removing protocol processing overhead from the host processor, thus providing for higher nett data throughput.

Dual channels provide redundant Gigabit Ethernet links for high system reliability with Redundant Link Management implemented in hardware managing unattended and automatic failure recovery of downed links.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Solaris, Windows 2000, Windows XP and Windows 2003 operating systems as standard; others optional.

CCII FDDI PMC: (from CCII Systems (Pty) Ltd)
Multimode fibre media. ST I/O Connectors. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel or rear facing I/O options.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Air-cooled option mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Video Capture and Compression PMC: (from CCII Systems (Pty) Ltd)
The Video Capture and Compression PMC Adapter generates a compressed video data stream from a standard RS-170 video source using MPEG4 compression implemented in hardware. This compressed video data stream can be output directly on one of four high-speed serial output channels or passed to a host computer via the PCI bus.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Available in three air-cooled grades : Ruggedised (-40 C to +85 C), Industrial (-15 C to +75 C) and Commerical (0 C to +55 C).

Interfaces to 32-bit, 33/66 MHz PCI-bus and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386-2001 specification.

Various software drivers offered including for VxWorks, Linux, Windows NT, Windows 2000* and Windows XP* operating systems as standard; others optional. (*Standard PC HAL only)

CL PMC/100: (from Concurrent Technologies)
10/100Mbps Fast Ethernet controller for VME, Multibus II and CompactPCI. Allows the use of 10BaseT or 100BaseTx with a slimline RJ45 connector. The chip is a highly integrated PCI single-chip bus master which supports direct memory access (DMA) and alleviates the Ethernet protocol load on the host CPU. Supporting ISO 8802-3 (IEEE 802.3 and 802.3u) the board has automatic retransmission, runt frame rejection and selection of received collision frames. Front panel LEDs indicate speed and status of the Local Area Network.

CL PMC/551 Dual Fast Ethernet: (from Concurrent Technologies)
PMC Ethernet Adaptor: A two channel Fast Ethernet adaptor with 10Base-T and 100Base-TX capability. The improved networking performance of the CL PMC/551 is achieved through the use of two Intel� 82551QM Fast Ethernet controllers. These controllers, which have 3Kbyte FIFOs and can operate full-duplex, enable the CL PMC/551 to exhibit improved performance by offloading the TCP, UDP and IP checksums and include support for TCP segmentation offload for operations such as Large Send. The controllers also have improved Bit Error Rate performance and improved dynamic transmit chaining with multiple priorities transmit queues. The adaptor´s physical connection to an Ethernet network is through industry standard RJ45 connectors that allow connection to low cost CAT 5 cabling. The adaptor is targeted at applications that will benefit from reducing the CPU´s Ethernet processing load while maintaining low system latency.

CL PMC/GB1 Dual Gigabit Copper Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.

CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: The 3059 is a single-port, fiber optic Ethernet adapter built around AMD 79C973. Fiber optic connector is ST TX/RX style. On-board flash memory for BIOS storage.
3293 -- i82559 Ethernet with Front and Rear IO: (from Technobox, Inc.)
The 3293 is a single-port 10/100-TX Ethernet PMC that can provide wither front or rear I/O connectivity as determined by DIP switch settings. Intel 82559. RJ45 jack and status/activity indicator LEDs on front panel. On-board flash memory holds BIOS for booting.

CCII CDDI PMC: (from CCII Systems (Pty) Ltd)
MLT-3 signalling over copper UTP media. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Dual 1 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
Dual, full-duplex, 1 Gbps Fibre Channel communication links on shielded, twisted-pair copper media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.

CCII Dual 2 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
Dual, full-duplex, 2 Gbps Fibre Channel communication links on short-haul or long-haul singlemode fibre media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Front-panel I/O only.

Available in three air-cooled grades: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Ruggedised version is ideally suited for environments with high temperature, shock and vibration levels.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.

CCII Dual 4 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
The Dual 4 Gbps Fibre Channel PMC Adapter offers dual 4 Gbps Fibre Channel communication links on multimode or singlemode fibre media. This adapter provides optimal flexibility by supporting all Fibre Channel topologies, including Arbitrated Loop, with full duplex communications on both channels.

Front-panel I/O only, SFF/LC connectors.

Available in three air-cooled grades : ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C).

Interfaces to 64-bit/133 MHz PCI-X (64-bit/66 MHz and 32-bit/33 MHz compatible) and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386 specification.

Various software drivers offered including for VxWorks, Windows 2000, Windows Server 2003, Windows XP, Solaris X86, Solaris SPARC, SUSE and Red Hat Linux operating systems as standard; others optional.

CCII Dual Gigabit Ethernet PMC: (from CCII Systems (Pty) Ltd)
Dual 10/100/1000 Mbps Ethernet communications links on either copper or fibre media. Uses a custom, intelligent ASIC for the control of the Gigabit Ethernet MACs (Media Access Controllers), thereby removing protocol processing overhead from the host processor, thus providing for higher nett data throughput.

Dual channels provide redundant Gigabit Ethernet links for high system reliability with Redundant Link Management implemented in hardware managing unattended and automatic failure recovery of downed links.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Solaris, Windows 2000, Windows XP and Windows 2003 operating systems as standard; others optional.

CCII FDDI PMC: (from CCII Systems (Pty) Ltd)
Multimode fibre media. ST I/O Connectors. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel or rear facing I/O options.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Air-cooled option mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Video Capture and Compression PMC: (from CCII Systems (Pty) Ltd)
The Video Capture and Compression PMC Adapter generates a compressed video data stream from a standard RS-170 video source using MPEG4 compression implemented in hardware. This compressed video data stream can be output directly on one of four high-speed serial output channels or passed to a host computer via the PCI bus.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Available in three air-cooled grades : Ruggedised (-40 C to +85 C), Industrial (-15 C to +75 C) and Commerical (0 C to +55 C).

Interfaces to 32-bit, 33/66 MHz PCI-bus and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386-2001 specification.

Various software drivers offered including for VxWorks, Linux, Windows NT, Windows 2000* and Windows XP* operating systems as standard; others optional. (*Standard PC HAL only)

CL PMC/100: (from Concurrent Technologies)
10/100Mbps Fast Ethernet controller for VME, Multibus II and CompactPCI. Allows the use of 10BaseT or 100BaseTx with a slimline RJ45 connector. The chip is a highly integrated PCI single-chip bus master which supports direct memory access (DMA) and alleviates the Ethernet protocol load on the host CPU. Supporting ISO 8802-3 (IEEE 802.3 and 802.3u) the board has automatic retransmission, runt frame rejection and selection of received collision frames. Front panel LEDs indicate speed and status of the Local Area Network.

CL PMC/551 Dual Fast Ethernet: (from Concurrent Technologies)
PMC Ethernet Adaptor: A two channel Fast Ethernet adaptor with 10Base-T and 100Base-TX capability. The improved networking performance of the CL PMC/551 is achieved through the use of two Intel� 82551QM Fast Ethernet controllers. These controllers, which have 3Kbyte FIFOs and can operate full-duplex, enable the CL PMC/551 to exhibit improved performance by offloading the TCP, UDP and IP checksums and include support for TCP segmentation offload for operations such as Large Send. The controllers also have improved Bit Error Rate performance and improved dynamic transmit chaining with multiple priorities transmit queues. The adaptor´s physical connection to an Ethernet network is through industry standard RJ45 connectors that allow connection to low cost CAT 5 cabling. The adaptor is targeted at applications that will benefit from reducing the CPU´s Ethernet processing load while maintaining low system latency.

CL PMC/GB1 Dual Gigabit Copper Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.

CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: The 3293 is a single-port 10/100-TX Ethernet PMC that can provide wither front or rear I/O connectivity as determined by DIP switch settings. Intel 82559. RJ45 jack and status/activity indicator LEDs on front panel. On-board flash memory holds BIOS for booting.
CCII CDDI PMC: (from CCII Systems (Pty) Ltd)
MLT-3 signalling over copper UTP media. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Dual 1 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
Dual, full-duplex, 1 Gbps Fibre Channel communication links on shielded, twisted-pair copper media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.

CCII Dual 2 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
Dual, full-duplex, 2 Gbps Fibre Channel communication links on short-haul or long-haul singlemode fibre media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Front-panel I/O only.

Available in three air-cooled grades: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Ruggedised version is ideally suited for environments with high temperature, shock and vibration levels.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.

CCII Dual 4 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
The Dual 4 Gbps Fibre Channel PMC Adapter offers dual 4 Gbps Fibre Channel communication links on multimode or singlemode fibre media. This adapter provides optimal flexibility by supporting all Fibre Channel topologies, including Arbitrated Loop, with full duplex communications on both channels.

Front-panel I/O only, SFF/LC connectors.

Available in three air-cooled grades : ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C).

Interfaces to 64-bit/133 MHz PCI-X (64-bit/66 MHz and 32-bit/33 MHz compatible) and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386 specification.

Various software drivers offered including for VxWorks, Windows 2000, Windows Server 2003, Windows XP, Solaris X86, Solaris SPARC, SUSE and Red Hat Linux operating systems as standard; others optional.

CCII Dual Gigabit Ethernet PMC: (from CCII Systems (Pty) Ltd)
Dual 10/100/1000 Mbps Ethernet communications links on either copper or fibre media. Uses a custom, intelligent ASIC for the control of the Gigabit Ethernet MACs (Media Access Controllers), thereby removing protocol processing overhead from the host processor, thus providing for higher nett data throughput.

Dual channels provide redundant Gigabit Ethernet links for high system reliability with Redundant Link Management implemented in hardware managing unattended and automatic failure recovery of downed links.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Solaris, Windows 2000, Windows XP and Windows 2003 operating systems as standard; others optional.

CCII FDDI PMC: (from CCII Systems (Pty) Ltd)
Multimode fibre media. ST I/O Connectors. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel or rear facing I/O options.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Air-cooled option mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Video Capture and Compression PMC: (from CCII Systems (Pty) Ltd)
The Video Capture and Compression PMC Adapter generates a compressed video data stream from a standard RS-170 video source using MPEG4 compression implemented in hardware. This compressed video data stream can be output directly on one of four high-speed serial output channels or passed to a host computer via the PCI bus.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Available in three air-cooled grades : Ruggedised (-40 C to +85 C), Industrial (-15 C to +75 C) and Commerical (0 C to +55 C).

Interfaces to 32-bit, 33/66 MHz PCI-bus and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386-2001 specification.

Various software drivers offered including for VxWorks, Linux, Windows NT, Windows 2000* and Windows XP* operating systems as standard; others optional. (*Standard PC HAL only)

CL PMC/100: (from Concurrent Technologies)
10/100Mbps Fast Ethernet controller for VME, Multibus II and CompactPCI. Allows the use of 10BaseT or 100BaseTx with a slimline RJ45 connector. The chip is a highly integrated PCI single-chip bus master which supports direct memory access (DMA) and alleviates the Ethernet protocol load on the host CPU. Supporting ISO 8802-3 (IEEE 802.3 and 802.3u) the board has automatic retransmission, runt frame rejection and selection of received collision frames. Front panel LEDs indicate speed and status of the Local Area Network.

CL PMC/551 Dual Fast Ethernet: (from Concurrent Technologies)
PMC Ethernet Adaptor: A two channel Fast Ethernet adaptor with 10Base-T and 100Base-TX capability. The improved networking performance of the CL PMC/551 is achieved through the use of two Intel� 82551QM Fast Ethernet controllers. These controllers, which have 3Kbyte FIFOs and can operate full-duplex, enable the CL PMC/551 to exhibit improved performance by offloading the TCP, UDP and IP checksums and include support for TCP segmentation offload for operations such as Large Send. The controllers also have improved Bit Error Rate performance and improved dynamic transmit chaining with multiple priorities transmit queues. The adaptor´s physical connection to an Ethernet network is through industry standard RJ45 connectors that allow connection to low cost CAT 5 cabling. The adaptor is targeted at applications that will benefit from reducing the CPU´s Ethernet processing load while maintaining low system latency.

CL PMC/GB1 Dual Gigabit Copper Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.

CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: MLT-3 signalling over copper UTP media. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.
CCII Dual 1 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
Dual, full-duplex, 1 Gbps Fibre Channel communication links on shielded, twisted-pair copper media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.

CCII Dual 2 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
Dual, full-duplex, 2 Gbps Fibre Channel communication links on short-haul or long-haul singlemode fibre media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Front-panel I/O only.

Available in three air-cooled grades: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Ruggedised version is ideally suited for environments with high temperature, shock and vibration levels.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.

CCII Dual 4 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
The Dual 4 Gbps Fibre Channel PMC Adapter offers dual 4 Gbps Fibre Channel communication links on multimode or singlemode fibre media. This adapter provides optimal flexibility by supporting all Fibre Channel topologies, including Arbitrated Loop, with full duplex communications on both channels.

Front-panel I/O only, SFF/LC connectors.

Available in three air-cooled grades : ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C).

Interfaces to 64-bit/133 MHz PCI-X (64-bit/66 MHz and 32-bit/33 MHz compatible) and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386 specification.

Various software drivers offered including for VxWorks, Windows 2000, Windows Server 2003, Windows XP, Solaris X86, Solaris SPARC, SUSE and Red Hat Linux operating systems as standard; others optional.

CCII Dual Gigabit Ethernet PMC: (from CCII Systems (Pty) Ltd)
Dual 10/100/1000 Mbps Ethernet communications links on either copper or fibre media. Uses a custom, intelligent ASIC for the control of the Gigabit Ethernet MACs (Media Access Controllers), thereby removing protocol processing overhead from the host processor, thus providing for higher nett data throughput.

Dual channels provide redundant Gigabit Ethernet links for high system reliability with Redundant Link Management implemented in hardware managing unattended and automatic failure recovery of downed links.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Solaris, Windows 2000, Windows XP and Windows 2003 operating systems as standard; others optional.

CCII FDDI PMC: (from CCII Systems (Pty) Ltd)
Multimode fibre media. ST I/O Connectors. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel or rear facing I/O options.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Air-cooled option mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Video Capture and Compression PMC: (from CCII Systems (Pty) Ltd)
The Video Capture and Compression PMC Adapter generates a compressed video data stream from a standard RS-170 video source using MPEG4 compression implemented in hardware. This compressed video data stream can be output directly on one of four high-speed serial output channels or passed to a host computer via the PCI bus.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Available in three air-cooled grades : Ruggedised (-40 C to +85 C), Industrial (-15 C to +75 C) and Commerical (0 C to +55 C).

Interfaces to 32-bit, 33/66 MHz PCI-bus and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386-2001 specification.

Various software drivers offered including for VxWorks, Linux, Windows NT, Windows 2000* and Windows XP* operating systems as standard; others optional. (*Standard PC HAL only)

CL PMC/100: (from Concurrent Technologies)
10/100Mbps Fast Ethernet controller for VME, Multibus II and CompactPCI. Allows the use of 10BaseT or 100BaseTx with a slimline RJ45 connector. The chip is a highly integrated PCI single-chip bus master which supports direct memory access (DMA) and alleviates the Ethernet protocol load on the host CPU. Supporting ISO 8802-3 (IEEE 802.3 and 802.3u) the board has automatic retransmission, runt frame rejection and selection of received collision frames. Front panel LEDs indicate speed and status of the Local Area Network.

CL PMC/551 Dual Fast Ethernet: (from Concurrent Technologies)
PMC Ethernet Adaptor: A two channel Fast Ethernet adaptor with 10Base-T and 100Base-TX capability. The improved networking performance of the CL PMC/551 is achieved through the use of two Intel� 82551QM Fast Ethernet controllers. These controllers, which have 3Kbyte FIFOs and can operate full-duplex, enable the CL PMC/551 to exhibit improved performance by offloading the TCP, UDP and IP checksums and include support for TCP segmentation offload for operations such as Large Send. The controllers also have improved Bit Error Rate performance and improved dynamic transmit chaining with multiple priorities transmit queues. The adaptor´s physical connection to an Ethernet network is through industry standard RJ45 connectors that allow connection to low cost CAT 5 cabling. The adaptor is targeted at applications that will benefit from reducing the CPU´s Ethernet processing load while maintaining low system latency.

CL PMC/GB1 Dual Gigabit Copper Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.

CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Dual, full-duplex, 1 Gbps Fibre Channel communication links on shielded, twisted-pair copper media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.
CCII Dual 2 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
Dual, full-duplex, 2 Gbps Fibre Channel communication links on short-haul or long-haul singlemode fibre media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Front-panel I/O only.

Available in three air-cooled grades: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Ruggedised version is ideally suited for environments with high temperature, shock and vibration levels.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.

CCII Dual 4 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
The Dual 4 Gbps Fibre Channel PMC Adapter offers dual 4 Gbps Fibre Channel communication links on multimode or singlemode fibre media. This adapter provides optimal flexibility by supporting all Fibre Channel topologies, including Arbitrated Loop, with full duplex communications on both channels.

Front-panel I/O only, SFF/LC connectors.

Available in three air-cooled grades : ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C).

Interfaces to 64-bit/133 MHz PCI-X (64-bit/66 MHz and 32-bit/33 MHz compatible) and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386 specification.

Various software drivers offered including for VxWorks, Windows 2000, Windows Server 2003, Windows XP, Solaris X86, Solaris SPARC, SUSE and Red Hat Linux operating systems as standard; others optional.

CCII Dual Gigabit Ethernet PMC: (from CCII Systems (Pty) Ltd)
Dual 10/100/1000 Mbps Ethernet communications links on either copper or fibre media. Uses a custom, intelligent ASIC for the control of the Gigabit Ethernet MACs (Media Access Controllers), thereby removing protocol processing overhead from the host processor, thus providing for higher nett data throughput.

Dual channels provide redundant Gigabit Ethernet links for high system reliability with Redundant Link Management implemented in hardware managing unattended and automatic failure recovery of downed links.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Solaris, Windows 2000, Windows XP and Windows 2003 operating systems as standard; others optional.

CCII FDDI PMC: (from CCII Systems (Pty) Ltd)
Multimode fibre media. ST I/O Connectors. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel or rear facing I/O options.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Air-cooled option mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Video Capture and Compression PMC: (from CCII Systems (Pty) Ltd)
The Video Capture and Compression PMC Adapter generates a compressed video data stream from a standard RS-170 video source using MPEG4 compression implemented in hardware. This compressed video data stream can be output directly on one of four high-speed serial output channels or passed to a host computer via the PCI bus.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Available in three air-cooled grades : Ruggedised (-40 C to +85 C), Industrial (-15 C to +75 C) and Commerical (0 C to +55 C).

Interfaces to 32-bit, 33/66 MHz PCI-bus and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386-2001 specification.

Various software drivers offered including for VxWorks, Linux, Windows NT, Windows 2000* and Windows XP* operating systems as standard; others optional. (*Standard PC HAL only)

CL PMC/100: (from Concurrent Technologies)
10/100Mbps Fast Ethernet controller for VME, Multibus II and CompactPCI. Allows the use of 10BaseT or 100BaseTx with a slimline RJ45 connector. The chip is a highly integrated PCI single-chip bus master which supports direct memory access (DMA) and alleviates the Ethernet protocol load on the host CPU. Supporting ISO 8802-3 (IEEE 802.3 and 802.3u) the board has automatic retransmission, runt frame rejection and selection of received collision frames. Front panel LEDs indicate speed and status of the Local Area Network.

CL PMC/551 Dual Fast Ethernet: (from Concurrent Technologies)
PMC Ethernet Adaptor: A two channel Fast Ethernet adaptor with 10Base-T and 100Base-TX capability. The improved networking performance of the CL PMC/551 is achieved through the use of two Intel� 82551QM Fast Ethernet controllers. These controllers, which have 3Kbyte FIFOs and can operate full-duplex, enable the CL PMC/551 to exhibit improved performance by offloading the TCP, UDP and IP checksums and include support for TCP segmentation offload for operations such as Large Send. The controllers also have improved Bit Error Rate performance and improved dynamic transmit chaining with multiple priorities transmit queues. The adaptor´s physical connection to an Ethernet network is through industry standard RJ45 connectors that allow connection to low cost CAT 5 cabling. The adaptor is targeted at applications that will benefit from reducing the CPU´s Ethernet processing load while maintaining low system latency.

CL PMC/GB1 Dual Gigabit Copper Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.

CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Dual, full-duplex, 2 Gbps Fibre Channel communication links on short-haul or long-haul singlemode fibre media. Supports all Fibre Channel topologies, including Arbitrated Loop.

Front-panel I/O only.

Available in three air-cooled grades: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Ruggedised version is ideally suited for environments with high temperature, shock and vibration levels.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Windows 2000 and Windows XP operating systems as standard; others optional.
CCII Dual 4 Gbps Fibre Channel PMC: (from CCII Systems (Pty) Ltd)
The Dual 4 Gbps Fibre Channel PMC Adapter offers dual 4 Gbps Fibre Channel communication links on multimode or singlemode fibre media. This adapter provides optimal flexibility by supporting all Fibre Channel topologies, including Arbitrated Loop, with full duplex communications on both channels.

Front-panel I/O only, SFF/LC connectors.

Available in three air-cooled grades : ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C).

Interfaces to 64-bit/133 MHz PCI-X (64-bit/66 MHz and 32-bit/33 MHz compatible) and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386 specification.

Various software drivers offered including for VxWorks, Windows 2000, Windows Server 2003, Windows XP, Solaris X86, Solaris SPARC, SUSE and Red Hat Linux operating systems as standard; others optional.

CCII Dual Gigabit Ethernet PMC: (from CCII Systems (Pty) Ltd)
Dual 10/100/1000 Mbps Ethernet communications links on either copper or fibre media. Uses a custom, intelligent ASIC for the control of the Gigabit Ethernet MACs (Media Access Controllers), thereby removing protocol processing overhead from the host processor, thus providing for higher nett data throughput.

Dual channels provide redundant Gigabit Ethernet links for high system reliability with Redundant Link Management implemented in hardware managing unattended and automatic failure recovery of downed links.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Solaris, Windows 2000, Windows XP and Windows 2003 operating systems as standard; others optional.

CCII FDDI PMC: (from CCII Systems (Pty) Ltd)
Multimode fibre media. ST I/O Connectors. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel or rear facing I/O options.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Air-cooled option mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Video Capture and Compression PMC: (from CCII Systems (Pty) Ltd)
The Video Capture and Compression PMC Adapter generates a compressed video data stream from a standard RS-170 video source using MPEG4 compression implemented in hardware. This compressed video data stream can be output directly on one of four high-speed serial output channels or passed to a host computer via the PCI bus.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Available in three air-cooled grades : Ruggedised (-40 C to +85 C), Industrial (-15 C to +75 C) and Commerical (0 C to +55 C).

Interfaces to 32-bit, 33/66 MHz PCI-bus and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386-2001 specification.

Various software drivers offered including for VxWorks, Linux, Windows NT, Windows 2000* and Windows XP* operating systems as standard; others optional. (*Standard PC HAL only)

CL PMC/100: (from Concurrent Technologies)
10/100Mbps Fast Ethernet controller for VME, Multibus II and CompactPCI. Allows the use of 10BaseT or 100BaseTx with a slimline RJ45 connector. The chip is a highly integrated PCI single-chip bus master which supports direct memory access (DMA) and alleviates the Ethernet protocol load on the host CPU. Supporting ISO 8802-3 (IEEE 802.3 and 802.3u) the board has automatic retransmission, runt frame rejection and selection of received collision frames. Front panel LEDs indicate speed and status of the Local Area Network.

CL PMC/551 Dual Fast Ethernet: (from Concurrent Technologies)
PMC Ethernet Adaptor: A two channel Fast Ethernet adaptor with 10Base-T and 100Base-TX capability. The improved networking performance of the CL PMC/551 is achieved through the use of two Intel� 82551QM Fast Ethernet controllers. These controllers, which have 3Kbyte FIFOs and can operate full-duplex, enable the CL PMC/551 to exhibit improved performance by offloading the TCP, UDP and IP checksums and include support for TCP segmentation offload for operations such as Large Send. The controllers also have improved Bit Error Rate performance and improved dynamic transmit chaining with multiple priorities transmit queues. The adaptor´s physical connection to an Ethernet network is through industry standard RJ45 connectors that allow connection to low cost CAT 5 cabling. The adaptor is targeted at applications that will benefit from reducing the CPU´s Ethernet processing load while maintaining low system latency.

CL PMC/GB1 Dual Gigabit Copper Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.

CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: The Dual 4 Gbps Fibre Channel PMC Adapter offers dual 4 Gbps Fibre Channel communication links on multimode or singlemode fibre media. This adapter provides optimal flexibility by supporting all Fibre Channel topologies, including Arbitrated Loop, with full duplex communications on both channels.

Front-panel I/O only, SFF/LC connectors.

Available in three air-cooled grades : ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C).

Interfaces to 64-bit/133 MHz PCI-X (64-bit/66 MHz and 32-bit/33 MHz compatible) and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386 specification.

Various software drivers offered including for VxWorks, Windows 2000, Windows Server 2003, Windows XP, Solaris X86, Solaris SPARC, SUSE and Red Hat Linux operating systems as standard; others optional.
CCII Dual Gigabit Ethernet PMC: (from CCII Systems (Pty) Ltd)
Dual 10/100/1000 Mbps Ethernet communications links on either copper or fibre media. Uses a custom, intelligent ASIC for the control of the Gigabit Ethernet MACs (Media Access Controllers), thereby removing protocol processing overhead from the host processor, thus providing for higher nett data throughput.

Dual channels provide redundant Gigabit Ethernet links for high system reliability with Redundant Link Management implemented in hardware managing unattended and automatic failure recovery of downed links.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Solaris, Windows 2000, Windows XP and Windows 2003 operating systems as standard; others optional.

CCII FDDI PMC: (from CCII Systems (Pty) Ltd)
Multimode fibre media. ST I/O Connectors. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel or rear facing I/O options.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Air-cooled option mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Video Capture and Compression PMC: (from CCII Systems (Pty) Ltd)
The Video Capture and Compression PMC Adapter generates a compressed video data stream from a standard RS-170 video source using MPEG4 compression implemented in hardware. This compressed video data stream can be output directly on one of four high-speed serial output channels or passed to a host computer via the PCI bus.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Available in three air-cooled grades : Ruggedised (-40 C to +85 C), Industrial (-15 C to +75 C) and Commerical (0 C to +55 C).

Interfaces to 32-bit, 33/66 MHz PCI-bus and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386-2001 specification.

Various software drivers offered including for VxWorks, Linux, Windows NT, Windows 2000* and Windows XP* operating systems as standard; others optional. (*Standard PC HAL only)

CL PMC/100: (from Concurrent Technologies)
10/100Mbps Fast Ethernet controller for VME, Multibus II and CompactPCI. Allows the use of 10BaseT or 100BaseTx with a slimline RJ45 connector. The chip is a highly integrated PCI single-chip bus master which supports direct memory access (DMA) and alleviates the Ethernet protocol load on the host CPU. Supporting ISO 8802-3 (IEEE 802.3 and 802.3u) the board has automatic retransmission, runt frame rejection and selection of received collision frames. Front panel LEDs indicate speed and status of the Local Area Network.

CL PMC/551 Dual Fast Ethernet: (from Concurrent Technologies)
PMC Ethernet Adaptor: A two channel Fast Ethernet adaptor with 10Base-T and 100Base-TX capability. The improved networking performance of the CL PMC/551 is achieved through the use of two Intel� 82551QM Fast Ethernet controllers. These controllers, which have 3Kbyte FIFOs and can operate full-duplex, enable the CL PMC/551 to exhibit improved performance by offloading the TCP, UDP and IP checksums and include support for TCP segmentation offload for operations such as Large Send. The controllers also have improved Bit Error Rate performance and improved dynamic transmit chaining with multiple priorities transmit queues. The adaptor´s physical connection to an Ethernet network is through industry standard RJ45 connectors that allow connection to low cost CAT 5 cabling. The adaptor is targeted at applications that will benefit from reducing the CPU´s Ethernet processing load while maintaining low system latency.

CL PMC/GB1 Dual Gigabit Copper Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.

CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Dual 10/100/1000 Mbps Ethernet communications links on either copper or fibre media. Uses a custom, intelligent ASIC for the control of the Gigabit Ethernet MACs (Media Access Controllers), thereby removing protocol processing overhead from the host processor, thus providing for higher nett data throughput.

Dual channels provide redundant Gigabit Ethernet links for high system reliability with Redundant Link Management implemented in hardware managing unattended and automatic failure recovery of downed links.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Interfaces to 64-bit 66 MHz PCI-bus (32-bit 33 MHz compatible) and complies with PCI Rev. 2.1 specification. Mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, Solaris, Windows 2000, Windows XP and Windows 2003 operating systems as standard; others optional.
CCII FDDI PMC: (from CCII Systems (Pty) Ltd)
Multimode fibre media. ST I/O Connectors. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel or rear facing I/O options.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Air-cooled option mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.

CCII Video Capture and Compression PMC: (from CCII Systems (Pty) Ltd)
The Video Capture and Compression PMC Adapter generates a compressed video data stream from a standard RS-170 video source using MPEG4 compression implemented in hardware. This compressed video data stream can be output directly on one of four high-speed serial output channels or passed to a host computer via the PCI bus.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Available in three air-cooled grades : Ruggedised (-40 C to +85 C), Industrial (-15 C to +75 C) and Commerical (0 C to +55 C).

Interfaces to 32-bit, 33/66 MHz PCI-bus and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386-2001 specification.

Various software drivers offered including for VxWorks, Linux, Windows NT, Windows 2000* and Windows XP* operating systems as standard; others optional. (*Standard PC HAL only)

CL PMC/100: (from Concurrent Technologies)
10/100Mbps Fast Ethernet controller for VME, Multibus II and CompactPCI. Allows the use of 10BaseT or 100BaseTx with a slimline RJ45 connector. The chip is a highly integrated PCI single-chip bus master which supports direct memory access (DMA) and alleviates the Ethernet protocol load on the host CPU. Supporting ISO 8802-3 (IEEE 802.3 and 802.3u) the board has automatic retransmission, runt frame rejection and selection of received collision frames. Front panel LEDs indicate speed and status of the Local Area Network.

CL PMC/551 Dual Fast Ethernet: (from Concurrent Technologies)
PMC Ethernet Adaptor: A two channel Fast Ethernet adaptor with 10Base-T and 100Base-TX capability. The improved networking performance of the CL PMC/551 is achieved through the use of two Intel� 82551QM Fast Ethernet controllers. These controllers, which have 3Kbyte FIFOs and can operate full-duplex, enable the CL PMC/551 to exhibit improved performance by offloading the TCP, UDP and IP checksums and include support for TCP segmentation offload for operations such as Large Send. The controllers also have improved Bit Error Rate performance and improved dynamic transmit chaining with multiple priorities transmit queues. The adaptor´s physical connection to an Ethernet network is through industry standard RJ45 connectors that allow connection to low cost CAT 5 cabling. The adaptor is targeted at applications that will benefit from reducing the CPU´s Ethernet processing load while maintaining low system latency.

CL PMC/GB1 Dual Gigabit Copper Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.

CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Multimode fibre media. ST I/O Connectors. Dual-Attachment Station (DAS) and Single-Attachment Station (SAS) options.

Available in conduction-cooled (-40 C to +85 C) and air-cooled versions: ruggedised (-40 C to +85 C), industrial (-15 C to +75 C) and commercial (0 C to +55 C). Conduction-cooled and ruggedised versions are ideally suited for environments with high temperature, shock and vibration levels.

Front-panel or rear facing I/O options.

Interfaces to 32-bit PCI-bus and complies with PCI Rev. 2.1 specification. Air-cooled option mechanically complies with single CMC formfactor i.a.w. IEEE P1386 specification.

Various software drivers offered including for VxWorks, Linux, LynxOS, Solaris, DOS, OS/2, Windows (95, 98, NT, 2000, XP and 2003) operating systems as standard; others optional.

Built-in Test (BIT) software optional.
CCII Video Capture and Compression PMC: (from CCII Systems (Pty) Ltd)
The Video Capture and Compression PMC Adapter generates a compressed video data stream from a standard RS-170 video source using MPEG4 compression implemented in hardware. This compressed video data stream can be output directly on one of four high-speed serial output channels or passed to a host computer via the PCI bus.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Available in three air-cooled grades : Ruggedised (-40 C to +85 C), Industrial (-15 C to +75 C) and Commerical (0 C to +55 C).

Interfaces to 32-bit, 33/66 MHz PCI-bus and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386-2001 specification.

Various software drivers offered including for VxWorks, Linux, Windows NT, Windows 2000* and Windows XP* operating systems as standard; others optional. (*Standard PC HAL only)

CL PMC/100: (from Concurrent Technologies)
10/100Mbps Fast Ethernet controller for VME, Multibus II and CompactPCI. Allows the use of 10BaseT or 100BaseTx with a slimline RJ45 connector. The chip is a highly integrated PCI single-chip bus master which supports direct memory access (DMA) and alleviates the Ethernet protocol load on the host CPU. Supporting ISO 8802-3 (IEEE 802.3 and 802.3u) the board has automatic retransmission, runt frame rejection and selection of received collision frames. Front panel LEDs indicate speed and status of the Local Area Network.

CL PMC/551 Dual Fast Ethernet: (from Concurrent Technologies)
PMC Ethernet Adaptor: A two channel Fast Ethernet adaptor with 10Base-T and 100Base-TX capability. The improved networking performance of the CL PMC/551 is achieved through the use of two Intel� 82551QM Fast Ethernet controllers. These controllers, which have 3Kbyte FIFOs and can operate full-duplex, enable the CL PMC/551 to exhibit improved performance by offloading the TCP, UDP and IP checksums and include support for TCP segmentation offload for operations such as Large Send. The controllers also have improved Bit Error Rate performance and improved dynamic transmit chaining with multiple priorities transmit queues. The adaptor´s physical connection to an Ethernet network is through industry standard RJ45 connectors that allow connection to low cost CAT 5 cabling. The adaptor is targeted at applications that will benefit from reducing the CPU´s Ethernet processing load while maintaining low system latency.

CL PMC/GB1 Dual Gigabit Copper Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.

CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: The Video Capture and Compression PMC Adapter generates a compressed video data stream from a standard RS-170 video source using MPEG4 compression implemented in hardware. This compressed video data stream can be output directly on one of four high-speed serial output channels or passed to a host computer via the PCI bus.

Front-panel and rear connector I/O options with various rear connector PMC Jn4 I/O pin assignments. Conduction-cooled version has rear connector I/O only.

Available in three air-cooled grades : Ruggedised (-40 C to +85 C), Industrial (-15 C to +75 C) and Commerical (0 C to +55 C).

Interfaces to 32-bit, 33/66 MHz PCI-bus and complies with PCI Rev. 2.2 specification. Mechanically complies with Single CMC formfactor IEEE P1386-2001 specification.

Various software drivers offered including for VxWorks, Linux, Windows NT, Windows 2000* and Windows XP* operating systems as standard; others optional. (*Standard PC HAL only)
CL PMC/100: (from Concurrent Technologies)
10/100Mbps Fast Ethernet controller for VME, Multibus II and CompactPCI. Allows the use of 10BaseT or 100BaseTx with a slimline RJ45 connector. The chip is a highly integrated PCI single-chip bus master which supports direct memory access (DMA) and alleviates the Ethernet protocol load on the host CPU. Supporting ISO 8802-3 (IEEE 802.3 and 802.3u) the board has automatic retransmission, runt frame rejection and selection of received collision frames. Front panel LEDs indicate speed and status of the Local Area Network.

CL PMC/551 Dual Fast Ethernet: (from Concurrent Technologies)
PMC Ethernet Adaptor: A two channel Fast Ethernet adaptor with 10Base-T and 100Base-TX capability. The improved networking performance of the CL PMC/551 is achieved through the use of two Intel� 82551QM Fast Ethernet controllers. These controllers, which have 3Kbyte FIFOs and can operate full-duplex, enable the CL PMC/551 to exhibit improved performance by offloading the TCP, UDP and IP checksums and include support for TCP segmentation offload for operations such as Large Send. The controllers also have improved Bit Error Rate performance and improved dynamic transmit chaining with multiple priorities transmit queues. The adaptor´s physical connection to an Ethernet network is through industry standard RJ45 connectors that allow connection to low cost CAT 5 cabling. The adaptor is targeted at applications that will benefit from reducing the CPU´s Ethernet processing load while maintaining low system latency.

CL PMC/GB1 Dual Gigabit Copper Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.

CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: 10/100Mbps Fast Ethernet controller for VME, Multibus II and CompactPCI. Allows the use of 10BaseT or 100BaseTx with a slimline RJ45 connector. The chip is a highly integrated PCI single-chip bus master which supports direct memory access (DMA) and alleviates the Ethernet protocol load on the host CPU. Supporting ISO 8802-3 (IEEE 802.3 and 802.3u) the board has automatic retransmission, runt frame rejection and selection of received collision frames. Front panel LEDs indicate speed and status of the Local Area Network.
CL PMC/551 Dual Fast Ethernet: (from Concurrent Technologies)
PMC Ethernet Adaptor: A two channel Fast Ethernet adaptor with 10Base-T and 100Base-TX capability. The improved networking performance of the CL PMC/551 is achieved through the use of two Intel� 82551QM Fast Ethernet controllers. These controllers, which have 3Kbyte FIFOs and can operate full-duplex, enable the CL PMC/551 to exhibit improved performance by offloading the TCP, UDP and IP checksums and include support for TCP segmentation offload for operations such as Large Send. The controllers also have improved Bit Error Rate performance and improved dynamic transmit chaining with multiple priorities transmit queues. The adaptor´s physical connection to an Ethernet network is through industry standard RJ45 connectors that allow connection to low cost CAT 5 cabling. The adaptor is targeted at applications that will benefit from reducing the CPU´s Ethernet processing load while maintaining low system latency.

CL PMC/GB1 Dual Gigabit Copper Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.

CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: PMC Ethernet Adaptor: A two channel Fast Ethernet adaptor with 10Base-T and 100Base-TX capability. The improved networking performance of the CL PMC/551 is achieved through the use of two Intel� 82551QM Fast Ethernet controllers. These controllers, which have 3Kbyte FIFOs and can operate full-duplex, enable the CL PMC/551 to exhibit improved performance by offloading the TCP, UDP and IP checksums and include support for TCP segmentation offload for operations such as Large Send. The controllers also have improved Bit Error Rate performance and improved dynamic transmit chaining with multiple priorities transmit queues. The adaptor´s physical connection to an Ethernet network is through industry standard RJ45 connectors that allow connection to low cost CAT 5 cabling. The adaptor is targeted at applications that will benefit from reducing the CPU´s Ethernet processing load while maintaining low system latency.
CL PMC/GB1 Dual Gigabit Copper Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.

CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Uses 2 x Intel� 82543 Gigabit Ethernet controllers, copper interface via dual RJ45 connectors supporting 10BaseT, 100BaseTX or 1000Base-T Ethernet interface.
CL PMC/GB2 Dual Gigabit Fiber Ethernet: (from Concurrent Technologies)
Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.

DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Uses 2 x Intel� 82543 Gigabit Ethernet controllers, fiber interface via dual SC optical supporting the IEEE 802.3z Gigabit Ethernet standard.
DMF: (from GE Fanuc)
Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)

FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Optional Data Mover Firmware for PMC664, PMC665 series (PMC665-x-DMF)
FDDI 8466: (from Creative Electronic Systems)
PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering

PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: PowerLink FDDI, multimode fiber interface with SC connectors, on-board integrated FDDI station management, 32-bit, zero-wait-state PCI DMA master, up to 80 MBytes/sec burst PCI DMA rate (measured), 128 KBytes local buffering
PGE2: (from Curtiss-Wright Controls, Inc.)
PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards

PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: PGE2 brings the high-bandwidth data communication of Gigabit Ethernet to your SBC applications. Fully backward compatible with 10BASE-T and 100BASE-TX networks, the PGE2 provides seamless integratation between your existing Ethernet hardware and the higher performance Gigabit Ethernet devices.

* 2 1 Gigabit Ethernet channel
* 64-bit/66 MHz CPU interface
* Air or conduction-cooled
* Supported by VxWorks and Linux
* Optional stacking connector allows mother board to support both the PGE2 and assigned CWCEC PMC carrier boards
PMC-100BT: (from SBS Technologies)
Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.

PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Single Channel 10/100BT Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Single RJ-45 on front panel or rear-panel I/O via P4.
PMC-3101: (from SBS Technologies)
Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.

PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Dual Channel 10/100 Fast Ethernet PMC Module. 3KB transmit and 3KB receive FIFOs. CSMA/CD interface controller. Two RJ-45 on front panel or rear-panel I/O via P4.
PMC-3120: (from SBS Technologies)
1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.

PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: 1000BaseT Gigabit Ethernet PMC Module. 16KB transmit and 48KB receive FIFOs. Auto-detection CSMA/CD interface controller. Front-panel RJ-45 connector.
PMC-650 Rugged 8-port GigE Switch: (from Curtiss-Wright Controls, Inc.)
The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.

PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: The PMC-650 is an eight-port rugged Gigabit Ethernet Switch and is a part of a family of Gigabit Ethernet switching and routing products from Curtiss-Wright Controls Embedded Computing. Enabling gigabit Ethernet connections of CPUs, cards, and chassis in VME or VPX systems, the PMC-650 is an ideal low cost solution for architecting simple Intra-Platform Networks (IPNs).

The PMC-650 is an 8-port Gigabit Ethernet switch packaged in the industry-standard PMC form factor. It provides wirespeed unmanaged Layer-2 switching capabilities and typically sits on any basecard with a PMC site (e.g. Digital Signal Processing (DSP), Single Board Computer (SBC), Carrier or a Custom card). Ethernet interfaces from these and other cards within a chassis can be connected to the PMC-650 to create network ready systems. The PMC-650 connects to the PCI bus for power only. It has no effect on the operation of the host PCI bus. No software driver is needed on the base cards. The PMC-650 is designed for rugged applications with backplane I/O and is offered in a full range of ruggedized air-cooled and conduction-cooled versions.
PMC-8260: (from SBS Technologies)
Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.

PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Intelligent Quad E1/T1 PMC Module based on the MPC8260 processor. Four E1 or T1 connections on front panel using RJ-45. 16MB DRAM. 4MB Flash. SCBus via rear-panel (P4). Serial port for status monitoring. VxWorks BSP and development kit available.
PMC-Arcnet: (from SBS Technologies)
ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.

PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: ARCNET controller. Physical interface for traditional isolated hybrid interface and isolated RS-485 differential interface. Front or back I/O support.
PMC-ENET: (from Curtiss-Wright Controls, Inc.)
The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver

PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: The PMC ENET is a PMC module which provides one 10/100 BaseTX (twisted pair) Ethernet� port and one EIA-232 serial port The module may be used to add these interfaces to the SVME/DMV-179 and SVME/DMV-181 SBCs. Driver support is provided for the VxWorks RTOS. The module is also suitable for deployment in commerical and rugged systems.

* One 10/100 BaseTX (twisted pair) Ethernet port
* IEEE 802.3u Auto-Negotiation support
* One EIA-232 serial port
* Serial port supported only on CHAMP-AV
* Front panel RJ-45 and Micro-D connectors
* Rear panel I/O also provided
* 33 MHz, 32-bit PCI interface
* Stacker option (PPMC compliant host)
* Status LEDs
* VxWorks device driver
PMC498: (from GE Fanuc)
10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.

PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: 10BaseT to 10Base-2 PMC media converter with rotary switch and 16 LEDs.
PMC610: (from GE Fanuc)
Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.

PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Quad Ethernet 10BaseT/100BaseTX. Available with front or rear panel I/O.
PMC661FX/ST: (from GE Fanuc)
Single 100BaseFX Ethernet Controller

PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Single 100BaseFX Ethernet Controller
PMC661J: (from GE Fanuc)
Single 10BaseT/100BaseTX PMC Ethernet Controller.

PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Single 10BaseT/100BaseTX PMC Ethernet Controller.
PMC662: (from GE Fanuc)
Single 100BaseVG connection

PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Single 100BaseVG connection
PMC663AUI: (from GE Fanuc)
Dual 10Base5 Ethernet Controller, rear I/O

PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Dual 10Base5 Ethernet Controller, rear I/O
PMC663FX: (from GE Fanuc)
With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.

PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: With dual 100Mbit Ethernet interfaces the PMC663FX PCI Mezzanine Card (PMC) card delivers highest networking performance. Two 100BaseFX channels are each capable of full duplex operation in 100Mbit. Each of the Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers. This assures continuous, full bandwidth operation with minimum PCI overhead. State of the art PCI/PCI bridge couples the Ethernet interfaces to the host PCI bus, assuring high performance with minimum PCI loading.
PMC663J/J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.

PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Dual 10BaseT/100BaseTX. Available with front and rear panel I/O.
PMC663J4: (from GE Fanuc)
Dual 10BaseT/100BaseTX, J4 connection

PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Dual 10BaseT/100BaseTX, J4 connection
PMC664: (from GE Fanuc)
Intelligent Dual 10BaseT/100BaseTX, i960 co-processor

PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Intelligent Dual 10BaseT/100BaseTX, i960 co-processor
PMC665-A: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor with Firmware

PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Intelligent Dual 100BaseFX, i960 co-processor with Firmware
PMC665-B: (from GE Fanuc)
Intelligent Dual 100BaseFX, i960 co-processor

PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Intelligent Dual 100BaseFX, i960 co-processor
PMC665-C: (from GE Fanuc)
Dual 100BaseFX

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Dual 100BaseFX
PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Intelligent Dual 10BaseFL, i960 co-processor
PMC665A: (from GE Fanuc)
Intelligent Dual 10BaseFL, i960 co-processor

PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Intelligent Dual 10BaseFL, i960 co-processor
PMC665ST: (from GE Fanuc)
Intelligent dual 100BaseFX Ethernet Controller with ST Connector.

PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Intelligent dual 100BaseFX Ethernet Controller with ST Connector.
PMC667: (from GE Fanuc)
Gigabit Ethernet

PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Gigabit Ethernet
PMC667: (from GE Fanuc)
Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.

PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Gigabit Ethernet Controller with connector options for SC, LC, VF-45 or MT-RJ.
PMC669: (from GE Fanuc)
Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.

PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Dual Gigabit Ethernet Controller. 64/66 Mhz PCI capable. Connector options for SC, LC, VF-45 or MT-RJ with SX or LX variants.
Available in Fiber or Copper variants.
PMC670: (from GE Fanuc)
Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.

PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Gigabit Ethernet controller - second generation. 64/66 Mhz PCI capable. Using 1000Base-SX (LX option is available), the PMC670 is capable of full duplex operation. The PMC670 Ethernet/PCI includes a powerful DMA engine with very deep FIFO buffers (64K byte). This assures continuous, full bandwidth operation with minimum PCI overhead. The PMC670 has four flavor of I/O connectivity, SC, LC, VF-45 or MT-RJ with SX or LX option.
PMC681: (from GE Fanuc)
Single 10BaseT/100baseTX with Front Panel rotary switch

PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Single 10BaseT/100baseTX with Front Panel rotary switch
PMC682: (from GE Fanuc)
Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.

PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Multipurpose I/O PMC card with 10/100 Ethernet connection and dual RS232/422/485 serial port with/without termination.
PMC683: (from GE Fanuc)
Dual 10Base2 Thinwire Ethernet Controller

PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Dual 10Base2 Thinwire Ethernet Controller
PMC684: (from GE Fanuc)
Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.

PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Multipurpose I/O PMC module with four independent 10/100TX Ethernet ports via J4 rear I/O and four independent serial ports [RS232/RS422/RS485). 16 general purpose I/O (eight input, eight output) + smart modem at 56K Baud.
PMC694: (from GE Fanuc)
Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.

TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Intelligent dual 10/100BaseTX PMC Ethernet Controller. On-board PowerPC 266MHz RISC processor and PCI bridge system for very high performance and extreme flexibility.
TPMC382-10: (from TEWS TECHNOLGIES GmbH)
Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C

TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Conduction Cooled PMC; 4 channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on rear I/O P14 connector; Operating temperature -40�C to +85�C
TPMC815-11: (from TEWS TECHNOLGIES GmbH)
ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C

TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: ARCNET Traditional Interface; COM20020 ARCNET controller, 5 Mbps; Traditional hybrid interface; BNC and DB9 mounted in front panel; Operating temperature 0�C to +70�C
TPMC815-21: (from TEWS TECHNOLGIES GmbH)
ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C

TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: ARCNET RS485 Interface; COM20020 ARCNET controller, 5 Mbps; Isolated RS485 interface; DB9 mounted in front panel; Operating temperature -40�C to +85�C
TPMC880-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C

TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Single 10/100BaseT and 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides both, 10/100BaseT on RJ45 connector and 10Base2 on BNC connector. Both connectors and status LED´s mounted in front panel; Operating temperature -0�C to +70�C
TPMC880-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Single 10/100BaseT Ethernet Interface based on Intel 21143 Controller. Provides 10/100BaseT interface on RJ45 connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C
TPMC880-12: (from TEWS TECHNOLGIES GmbH)
Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C

TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Single 10Base2 Ethernet Interface based on Intel 21143 Controller. Provides 10Base2 interface on BNC connector. Connector and status LED´s mounted in front panel; Operating temperature 0�C to +70�C
TPMC881-10: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C
TPMC881-10-ET: (from TEWS TECHNOLGIES GmbH)
Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C

TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on RJ45 connector with status LED´s in front panel; Operating temperature -40�C to +85�C
TPMC881-11: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C

TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature 0�C to +70�C
TPMC881-11-ET: (from TEWS TECHNOLGIES GmbH)
Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C

TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Single 10/100BaseT Ethernet Interface; Ethernet interface based on Intel 82551 Controller. Provides single channel 10/100BaseT on rear I/O P14; sttatus LED´s in front panel; Operating temperature -40�C to +85�C
TPMC882-10: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C

TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on RJ45 connector in front panel; Operating temperature -40�C to +85�C
TPMC882-11: (from TEWS TECHNOLGIES GmbH)
Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C

TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Four channel Ethernet interface; each channel based on Intel 82551 Controller providing 10/100BaseT on P14 I/O; Operating temperature -40�C to +85�C
TPMC883-10: (from TEWS TECHNOLGIES GmbH)
Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C

TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Single Channel Gigabit Ethernet Interface based on Intel 82545EM Controller. Provides single channel 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +70�C
TPMC884-10: (from TEWS TECHNOLGIES GmbH)
Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C

VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Dual Channel Gigabit Ethernet Interface based on Intel 82546EB Controller. Provides two channels 10/100/1000BaseTX on RJ45 connector with status LED´s in front panel; Operating temperature 0�C to +55�C
VMIPMC-5576XL: (from GE Fanuc)
Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.

VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: Single PCI mezzanine card (PMC), High-speed, Reflective Memory fiber-optic network (170 Mbaud serially). PCI target burst supported w/33MB/s transfer rates, data transferred at 6.2MB/s without redundant transfer and 3.2MB/s with redundant transfer. IEEE 1386.1 PMC compatible and has networking compatibility with VMIC's 5576 family which include the following buses, VME, PCI, CPCI, Multibus, and GE90-30.
VMIPMC-5579: (from GE Fanuc)
A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.

VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: A real-time networking product that uses the technology referred to in the industry as Reflective Memory. This product has a data transfer rate of 13.4 Mbyte/s and a 270 Mbaud network speed. Data can be shared among up to 256 independent systems (nodes) and is connected by fiber-optic cable up to 2,000 feet. PCI and CompactPCI versions also available.
VMIPMC-5660: (from GE Fanuc)
This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.

VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: This PMC 1 Gigabit Fibre Channel Adapter is a single-board, highly intergrated (HBA). It is specifically designed for storage area network (SAN) applications, and computer clustering. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications. The HBA connects the PMC bus to a Fibre Channel loop, fabric or to a point-to-point network. It maximizes Fibre Channel throughput while minimizing transfer latency and host processor overhead.
VMIPMC-5661: (from GE Fanuc)
PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.: PMC 1 Gigabit Fibre Channel Adapter is a single-board, that is highly intergrated. It is specifically designed for storage area network (SAN) applications. Typical applications include enterprise-wide and workgroup configurations that consolidate hard disk arrays and tape library functions at a central location. It is well suited for telecom, signal processing, and distributed computing applications.