Adapters

Home

Vendors

Products

Adapters

cPCI2IP: (from Dynamic Engineering)
The cPCI [CompactPCI] compatible cPCI2IP design adds 2 Industrypack compatible slots to your cPCI host. The cPCI2IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI2IP is a 3U 4HP cPCI design with 2 IP slots, 32 bit IP Module support, Big and little endian support and Improved bus error handling.

HDETerm68: (from Dynamic Engineering)
SCSI II/III to 68 Terminal positions SCSI II/III adapter to terminal strip with DIN rail and custom termination options

HDRterm50 - terminal board: (from Dynamic Engineering)
Ribbon cable to terminal strip adapter. HDRterm50 will make your IndustryPack system inter-connection easier providing an interconnection method between 50 pin ribbon cable and discrete wiring systems.

HDRterm50 - terminal board: (from Dynamic Engineering)
HDRterm50 will make your IndustryPack system inter-connection easier providing an interconnection method between 50 pin ribbon cable and discrete wiring systems.

IP-CF IndustryPack(tm) CompactFlash(tm) adapter: (from Dynamic Engineering)
Add solid state data storage to your system with IP-CF. The IndustryPack compatible IP-CF design converts between the IP Module bus and the IDE bus used for FLASH memory modules and other PC Card compatible designs. The IP-CF acts as a bridge between the IP bus and your PC Card hardware. The IP-CF comes standard with a 64 Mb CompactFLASH (tm) card.

IP-H009: (from SBS Technologies)
H009, Primary and redundant interface to F-15 Avionics Bus, 3 ports each interface.

IP-Thermistor: (from SBS Technologies)
Temperature Thermistor Interface, 16 CH, 12-bit ADC for Thermistor-based sensors accurate temperature measurement.

PCI3IP PCI carrier w/3 IP slots & Windows Drivers: (from Dynamic Engineering)
PCI3IP-XP Windows®XP/2000 Driver for PCI3IP now shipping
 
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. PCI-3-IP is a half size PCI card compatible with the smallest chassis and the tallest processors that prevent full size solutions. Each slot has a separate clock controller for 8 and 32 MHz operation. The clocks are locked together allowing the frequency to be changed on the fly without creating glitches. Each slot has resettable fused filtered power. The power is distributed to provide isolation between the slots. 50 pin headers are used with the IO connectors. Vertical connectors are provided in all positions. Slots A and B are configured to allow double wide Industrypack compatible operation. A reset switch is provided for the IP boards. The PCI interface should only be reset via the backplane so that system addressing information is not lost. LEDs are provided for each of the IPs activity and power indicators on slot A. An additional six user LEDs are available for debugging or other purposes. A surface mount "dip switch" is available for configuration control or debugging purposes. The switch values are available to be read via the PCI bus. 32 bit accesses to the IP slots result in a double cycle to the IP saving PCI overhead. Byte, Word and Long Word. 

PCI5IP: (from Dynamic Engineering)
The PCI compatible PCI5IP design adds 5 Industrypack compatible slots to your PCI host. The PCI5IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI5IP is a full size PCI card with 5 IP sites.

PMC2PCI: (from Dynamic Engineering)
The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.: The cPCI [CompactPCI] compatible cPCI2IP design adds 2 Industrypack compatible slots to your cPCI host. The cPCI2IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI2IP is a 3U 4HP cPCI design with 2 IP slots, 32 bit IP Module support, Big and little endian support and Improved bus error handling.
HDETerm68: (from Dynamic Engineering)
SCSI II/III to 68 Terminal positions SCSI II/III adapter to terminal strip with DIN rail and custom termination options

HDRterm50 - terminal board: (from Dynamic Engineering)
Ribbon cable to terminal strip adapter. HDRterm50 will make your IndustryPack system inter-connection easier providing an interconnection method between 50 pin ribbon cable and discrete wiring systems.

HDRterm50 - terminal board: (from Dynamic Engineering)
HDRterm50 will make your IndustryPack system inter-connection easier providing an interconnection method between 50 pin ribbon cable and discrete wiring systems.

IP-CF IndustryPack(tm) CompactFlash(tm) adapter: (from Dynamic Engineering)
Add solid state data storage to your system with IP-CF. The IndustryPack compatible IP-CF design converts between the IP Module bus and the IDE bus used for FLASH memory modules and other PC Card compatible designs. The IP-CF acts as a bridge between the IP bus and your PC Card hardware. The IP-CF comes standard with a 64 Mb CompactFLASH (tm) card.

IP-H009: (from SBS Technologies)
H009, Primary and redundant interface to F-15 Avionics Bus, 3 ports each interface.

IP-Thermistor: (from SBS Technologies)
Temperature Thermistor Interface, 16 CH, 12-bit ADC for Thermistor-based sensors accurate temperature measurement.

PCI3IP PCI carrier w/3 IP slots & Windows Drivers: (from Dynamic Engineering)
PCI3IP-XP Windows®XP/2000 Driver for PCI3IP now shipping
 
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. PCI-3-IP is a half size PCI card compatible with the smallest chassis and the tallest processors that prevent full size solutions. Each slot has a separate clock controller for 8 and 32 MHz operation. The clocks are locked together allowing the frequency to be changed on the fly without creating glitches. Each slot has resettable fused filtered power. The power is distributed to provide isolation between the slots. 50 pin headers are used with the IO connectors. Vertical connectors are provided in all positions. Slots A and B are configured to allow double wide Industrypack compatible operation. A reset switch is provided for the IP boards. The PCI interface should only be reset via the backplane so that system addressing information is not lost. LEDs are provided for each of the IPs activity and power indicators on slot A. An additional six user LEDs are available for debugging or other purposes. A surface mount "dip switch" is available for configuration control or debugging purposes. The switch values are available to be read via the PCI bus. 32 bit accesses to the IP slots result in a double cycle to the IP saving PCI overhead. Byte, Word and Long Word. 

PCI5IP: (from Dynamic Engineering)
The PCI compatible PCI5IP design adds 5 Industrypack compatible slots to your PCI host. The PCI5IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI5IP is a full size PCI card with 5 IP sites.

PMC2PCI: (from Dynamic Engineering)
The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.: SCSI II/III to 68 Terminal positions SCSI II/III adapter to terminal strip with DIN rail and custom termination options
HDRterm50 - terminal board: (from Dynamic Engineering)
Ribbon cable to terminal strip adapter. HDRterm50 will make your IndustryPack system inter-connection easier providing an interconnection method between 50 pin ribbon cable and discrete wiring systems.

HDRterm50 - terminal board: (from Dynamic Engineering)
HDRterm50 will make your IndustryPack system inter-connection easier providing an interconnection method between 50 pin ribbon cable and discrete wiring systems.

IP-CF IndustryPack(tm) CompactFlash(tm) adapter: (from Dynamic Engineering)
Add solid state data storage to your system with IP-CF. The IndustryPack compatible IP-CF design converts between the IP Module bus and the IDE bus used for FLASH memory modules and other PC Card compatible designs. The IP-CF acts as a bridge between the IP bus and your PC Card hardware. The IP-CF comes standard with a 64 Mb CompactFLASH (tm) card.

IP-H009: (from SBS Technologies)
H009, Primary and redundant interface to F-15 Avionics Bus, 3 ports each interface.

IP-Thermistor: (from SBS Technologies)
Temperature Thermistor Interface, 16 CH, 12-bit ADC for Thermistor-based sensors accurate temperature measurement.

PCI3IP PCI carrier w/3 IP slots & Windows Drivers: (from Dynamic Engineering)
PCI3IP-XP Windows®XP/2000 Driver for PCI3IP now shipping
 
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. PCI-3-IP is a half size PCI card compatible with the smallest chassis and the tallest processors that prevent full size solutions. Each slot has a separate clock controller for 8 and 32 MHz operation. The clocks are locked together allowing the frequency to be changed on the fly without creating glitches. Each slot has resettable fused filtered power. The power is distributed to provide isolation between the slots. 50 pin headers are used with the IO connectors. Vertical connectors are provided in all positions. Slots A and B are configured to allow double wide Industrypack compatible operation. A reset switch is provided for the IP boards. The PCI interface should only be reset via the backplane so that system addressing information is not lost. LEDs are provided for each of the IPs activity and power indicators on slot A. An additional six user LEDs are available for debugging or other purposes. A surface mount "dip switch" is available for configuration control or debugging purposes. The switch values are available to be read via the PCI bus. 32 bit accesses to the IP slots result in a double cycle to the IP saving PCI overhead. Byte, Word and Long Word. 

PCI5IP: (from Dynamic Engineering)
The PCI compatible PCI5IP design adds 5 Industrypack compatible slots to your PCI host. The PCI5IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI5IP is a full size PCI card with 5 IP sites.

PMC2PCI: (from Dynamic Engineering)
The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.: Ribbon cable to terminal strip adapter. HDRterm50 will make your IndustryPack system inter-connection easier providing an interconnection method between 50 pin ribbon cable and discrete wiring systems.
HDRterm50 - terminal board: (from Dynamic Engineering)
HDRterm50 will make your IndustryPack system inter-connection easier providing an interconnection method between 50 pin ribbon cable and discrete wiring systems.

IP-CF IndustryPack(tm) CompactFlash(tm) adapter: (from Dynamic Engineering)
Add solid state data storage to your system with IP-CF. The IndustryPack compatible IP-CF design converts between the IP Module bus and the IDE bus used for FLASH memory modules and other PC Card compatible designs. The IP-CF acts as a bridge between the IP bus and your PC Card hardware. The IP-CF comes standard with a 64 Mb CompactFLASH (tm) card.

IP-H009: (from SBS Technologies)
H009, Primary and redundant interface to F-15 Avionics Bus, 3 ports each interface.

IP-Thermistor: (from SBS Technologies)
Temperature Thermistor Interface, 16 CH, 12-bit ADC for Thermistor-based sensors accurate temperature measurement.

PCI3IP PCI carrier w/3 IP slots & Windows Drivers: (from Dynamic Engineering)
PCI3IP-XP Windows®XP/2000 Driver for PCI3IP now shipping
 
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. PCI-3-IP is a half size PCI card compatible with the smallest chassis and the tallest processors that prevent full size solutions. Each slot has a separate clock controller for 8 and 32 MHz operation. The clocks are locked together allowing the frequency to be changed on the fly without creating glitches. Each slot has resettable fused filtered power. The power is distributed to provide isolation between the slots. 50 pin headers are used with the IO connectors. Vertical connectors are provided in all positions. Slots A and B are configured to allow double wide Industrypack compatible operation. A reset switch is provided for the IP boards. The PCI interface should only be reset via the backplane so that system addressing information is not lost. LEDs are provided for each of the IPs activity and power indicators on slot A. An additional six user LEDs are available for debugging or other purposes. A surface mount "dip switch" is available for configuration control or debugging purposes. The switch values are available to be read via the PCI bus. 32 bit accesses to the IP slots result in a double cycle to the IP saving PCI overhead. Byte, Word and Long Word. 

PCI5IP: (from Dynamic Engineering)
The PCI compatible PCI5IP design adds 5 Industrypack compatible slots to your PCI host. The PCI5IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI5IP is a full size PCI card with 5 IP sites.

PMC2PCI: (from Dynamic Engineering)
The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.: HDRterm50 will make your IndustryPack system inter-connection easier providing an interconnection method between 50 pin ribbon cable and discrete wiring systems.
IP-CF IndustryPack(tm) CompactFlash(tm) adapter: (from Dynamic Engineering)
Add solid state data storage to your system with IP-CF. The IndustryPack compatible IP-CF design converts between the IP Module bus and the IDE bus used for FLASH memory modules and other PC Card compatible designs. The IP-CF acts as a bridge between the IP bus and your PC Card hardware. The IP-CF comes standard with a 64 Mb CompactFLASH (tm) card.

IP-H009: (from SBS Technologies)
H009, Primary and redundant interface to F-15 Avionics Bus, 3 ports each interface.

IP-Thermistor: (from SBS Technologies)
Temperature Thermistor Interface, 16 CH, 12-bit ADC for Thermistor-based sensors accurate temperature measurement.

PCI3IP PCI carrier w/3 IP slots & Windows Drivers: (from Dynamic Engineering)
PCI3IP-XP Windows®XP/2000 Driver for PCI3IP now shipping
 
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. PCI-3-IP is a half size PCI card compatible with the smallest chassis and the tallest processors that prevent full size solutions. Each slot has a separate clock controller for 8 and 32 MHz operation. The clocks are locked together allowing the frequency to be changed on the fly without creating glitches. Each slot has resettable fused filtered power. The power is distributed to provide isolation between the slots. 50 pin headers are used with the IO connectors. Vertical connectors are provided in all positions. Slots A and B are configured to allow double wide Industrypack compatible operation. A reset switch is provided for the IP boards. The PCI interface should only be reset via the backplane so that system addressing information is not lost. LEDs are provided for each of the IPs activity and power indicators on slot A. An additional six user LEDs are available for debugging or other purposes. A surface mount "dip switch" is available for configuration control or debugging purposes. The switch values are available to be read via the PCI bus. 32 bit accesses to the IP slots result in a double cycle to the IP saving PCI overhead. Byte, Word and Long Word. 

PCI5IP: (from Dynamic Engineering)
The PCI compatible PCI5IP design adds 5 Industrypack compatible slots to your PCI host. The PCI5IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI5IP is a full size PCI card with 5 IP sites.

PMC2PCI: (from Dynamic Engineering)
The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.: Add solid state data storage to your system with IP-CF. The IndustryPack compatible IP-CF design converts between the IP Module bus and the IDE bus used for FLASH memory modules and other PC Card compatible designs. The IP-CF acts as a bridge between the IP bus and your PC Card hardware. The IP-CF comes standard with a 64 Mb CompactFLASH (tm) card.
IP-H009: (from SBS Technologies)
H009, Primary and redundant interface to F-15 Avionics Bus, 3 ports each interface.

IP-Thermistor: (from SBS Technologies)
Temperature Thermistor Interface, 16 CH, 12-bit ADC for Thermistor-based sensors accurate temperature measurement.

PCI3IP PCI carrier w/3 IP slots & Windows Drivers: (from Dynamic Engineering)
PCI3IP-XP Windows®XP/2000 Driver for PCI3IP now shipping
 
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. PCI-3-IP is a half size PCI card compatible with the smallest chassis and the tallest processors that prevent full size solutions. Each slot has a separate clock controller for 8 and 32 MHz operation. The clocks are locked together allowing the frequency to be changed on the fly without creating glitches. Each slot has resettable fused filtered power. The power is distributed to provide isolation between the slots. 50 pin headers are used with the IO connectors. Vertical connectors are provided in all positions. Slots A and B are configured to allow double wide Industrypack compatible operation. A reset switch is provided for the IP boards. The PCI interface should only be reset via the backplane so that system addressing information is not lost. LEDs are provided for each of the IPs activity and power indicators on slot A. An additional six user LEDs are available for debugging or other purposes. A surface mount "dip switch" is available for configuration control or debugging purposes. The switch values are available to be read via the PCI bus. 32 bit accesses to the IP slots result in a double cycle to the IP saving PCI overhead. Byte, Word and Long Word. 

PCI5IP: (from Dynamic Engineering)
The PCI compatible PCI5IP design adds 5 Industrypack compatible slots to your PCI host. The PCI5IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI5IP is a full size PCI card with 5 IP sites.

PMC2PCI: (from Dynamic Engineering)
The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.: H009, Primary and redundant interface to F-15 Avionics Bus, 3 ports each interface.
IP-Thermistor: (from SBS Technologies)
Temperature Thermistor Interface, 16 CH, 12-bit ADC for Thermistor-based sensors accurate temperature measurement.

PCI3IP PCI carrier w/3 IP slots & Windows Drivers: (from Dynamic Engineering)
PCI3IP-XP Windows®XP/2000 Driver for PCI3IP now shipping
 
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. PCI-3-IP is a half size PCI card compatible with the smallest chassis and the tallest processors that prevent full size solutions. Each slot has a separate clock controller for 8 and 32 MHz operation. The clocks are locked together allowing the frequency to be changed on the fly without creating glitches. Each slot has resettable fused filtered power. The power is distributed to provide isolation between the slots. 50 pin headers are used with the IO connectors. Vertical connectors are provided in all positions. Slots A and B are configured to allow double wide Industrypack compatible operation. A reset switch is provided for the IP boards. The PCI interface should only be reset via the backplane so that system addressing information is not lost. LEDs are provided for each of the IPs activity and power indicators on slot A. An additional six user LEDs are available for debugging or other purposes. A surface mount "dip switch" is available for configuration control or debugging purposes. The switch values are available to be read via the PCI bus. 32 bit accesses to the IP slots result in a double cycle to the IP saving PCI overhead. Byte, Word and Long Word. 

PCI5IP: (from Dynamic Engineering)
The PCI compatible PCI5IP design adds 5 Industrypack compatible slots to your PCI host. The PCI5IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI5IP is a full size PCI card with 5 IP sites.

PMC2PCI: (from Dynamic Engineering)
The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.: Temperature Thermistor Interface, 16 CH, 12-bit ADC for Thermistor-based sensors accurate temperature measurement.
PCI3IP PCI carrier w/3 IP slots & Windows Drivers: (from Dynamic Engineering)
PCI3IP-XP Windows®XP/2000 Driver for PCI3IP now shipping
 
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. PCI-3-IP is a half size PCI card compatible with the smallest chassis and the tallest processors that prevent full size solutions. Each slot has a separate clock controller for 8 and 32 MHz operation. The clocks are locked together allowing the frequency to be changed on the fly without creating glitches. Each slot has resettable fused filtered power. The power is distributed to provide isolation between the slots. 50 pin headers are used with the IO connectors. Vertical connectors are provided in all positions. Slots A and B are configured to allow double wide Industrypack compatible operation. A reset switch is provided for the IP boards. The PCI interface should only be reset via the backplane so that system addressing information is not lost. LEDs are provided for each of the IPs activity and power indicators on slot A. An additional six user LEDs are available for debugging or other purposes. A surface mount "dip switch" is available for configuration control or debugging purposes. The switch values are available to be read via the PCI bus. 32 bit accesses to the IP slots result in a double cycle to the IP saving PCI overhead. Byte, Word and Long Word. 

PCI5IP: (from Dynamic Engineering)
The PCI compatible PCI5IP design adds 5 Industrypack compatible slots to your PCI host. The PCI5IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI5IP is a full size PCI card with 5 IP sites.

PMC2PCI: (from Dynamic Engineering)
The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.: PCI3IP-XP Windows®XP/2000 Driver for PCI3IP now shipping
 
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. PCI-3-IP is a half size PCI card compatible with the smallest chassis and the tallest processors that prevent full size solutions. Each slot has a separate clock controller for 8 and 32 MHz operation. The clocks are locked together allowing the frequency to be changed on the fly without creating glitches. Each slot has resettable fused filtered power. The power is distributed to provide isolation between the slots. 50 pin headers are used with the IO connectors. Vertical connectors are provided in all positions. Slots A and B are configured to allow double wide Industrypack compatible operation. A reset switch is provided for the IP boards. The PCI interface should only be reset via the backplane so that system addressing information is not lost. LEDs are provided for each of the IPs activity and power indicators on slot A. An additional six user LEDs are available for debugging or other purposes. A surface mount "dip switch" is available for configuration control or debugging purposes. The switch values are available to be read via the PCI bus. 32 bit accesses to the IP slots result in a double cycle to the IP saving PCI overhead. Byte, Word and Long Word.
PCI5IP: (from Dynamic Engineering)
The PCI compatible PCI5IP design adds 5 Industrypack compatible slots to your PCI host. The PCI5IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI5IP is a full size PCI card with 5 IP sites.

PMC2PCI: (from Dynamic Engineering)
The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.: The PCI compatible PCI5IP design adds 5 Industrypack compatible slots to your PCI host. The PCI5IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI5IP is a full size PCI card with 5 IP sites.
PMC2PCI: (from Dynamic Engineering)
The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.: The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.